Skip to the content
Drive-Thru SOSGUIDE
All topics (3 of 13)
  1. 1What the board does
  2. 2Before you start
  3. 3Where to put the cameras
  4. 4Which lane type is mine?
  5. 5Set up the board
  6. 6Goals, the screen and alerts
  7. 7Using the board every day
  8. 8A TV with no PC: HDMI
  9. 9Reports
  10. 10Where alerts and reports go
  11. 11How the times are measured
  12. 12When something looks wrong
  13. 13Setup checklist

Drive-Thru SOS › Guide › Where to put the cameras

3Where to put the cameras

Every point you time must be seen by a camera. For the best accuracy, the cameras go on the building wall, on the same side as the menu board and the windows. These are the same instructions as the gateway's own setup guide (Board settings › Setup guide › Where to put the cameras), which also shows them animated.

Restaurant Pickup Pay Menu 1 2 At the window, aimed away: the stopped car is out of the picture Across the lot: car too small
From above. Camera 1 (the menu board) and camera 2 (the pickup window), both on the building, on the same side as the menu and the windows, past their stop, aimed back at the car standing there. A pay window that is a stop of its own gets one the same way. Red: two poor spots.
wall 15 to 30° down 2.4-3 m 8-10 ft 4-8 m (13-26 ft) to where the car stops
From the side. On the wall, low enough to see the car's front and side, high enough to look over the roof of the car behind it. Never more than 45° down, never straight down: from above a car is only a roof.

Where

  • One camera for each stop: the menu board, the pay window, the pickup window. One camera may watch two stops only if both stopped cars are whole in its picture and each fills at least a quarter of its width.
  • On the building, on the same side as the menu board and the windows, past the stop, looking back at the stopped car: it sees the car's front and the driver's side, and the next car in line stays behind it.
  • Pickup and pay window: on the wall 4-6 m (13-20 ft) past the window, toward the exit, aimed back along the wall and turned 15-25° out from it, so the car at the window is whole in the picture. Never right at the window: the stopped car is then under the camera, cut off by the picture's edge, and the AI loses it.
  • Menu board: on the building wall or corner past the menu, aimed back at the car at the menu the same way. A menu far from the building: a longer lens, so the car still fills a third of the picture.
  • 2.4-3 m (8-10 ft) up, 4-8 m (13-26 ft) from where the car stops, tilted 15-30° down.

In the picture

  • The whole stopped car, about a third to half of the picture's width, with some road around it.
  • The stop in the middle or lower half of the picture, away from every edge: a car cut by the edge is seen in pieces, and one stop splits into several.
  • Nothing between the camera and the stopped car: no pole, sign, speaker post or menu board.
  • The road leading in, so each car is followed before it stops.
  • One lane per camera where two lanes run side by side.

Camera settings, light, steadiness

  • Second stream (the one the AI reads): 704×480 (D1) or 1280×720, never 352×288 (CIF). 10-15 pictures a second, a keyframe every 1-2 seconds, H.264 or H.265. The gateway reads it and never changes the camera's settings.
  • Main stream 2 MP (1920×1080) or more, for recordings and the bigger drawing picture.
  • Lens about 4 mm at 4-6 m, 6 mm at 6-8 m; a varifocal 2.8-12 mm frames the car exactly. A 2.8 mm shows the car smaller, about a fifth of the picture at 5 m: it works, a third is better.
  • Light: at night the camera's IR, or a light over the stop, with WDR on. Not facing headlights, the menu board's light or the low sun straight on. In infrared the cars' colours show in grey; the times are not affected.
  • Keep it steady: a fixed camera, or a PTZ parked on one preset with no tour. A camera moved after drawing needs its zones drawn again. The video must reach the gateway steadily: the recorder on the store's network, or reachable directly.
  • The cars keep their order between cameras (first in, first out, as loop-sensor timers do), so nothing special is needed between cameras.
Already have cameras?Move or set each one as close to this as you can. After mounting, check with one car: at each stop the car is whole and near the middle of the picture, and in the drawing picture its dot turns green inside the zone. The board's Check the cameras (Board settings › Lane) then grades each point from its camera's last 24 hours.
About the pictures in this guideThe demonstration restaurant's two cameras, A (the line and the menu board) and B (the pay and pickup windows), look at the lane from across it, so that the whole site shows in each picture. Mount your own cameras on the building, as above.

Stuck on a step?

iLink Professionals supports owners and installers. Call, or send us a message.